klionmagazine.blogg.se - Metro e loopback plug

#Metro e loopback plug code
#Metro e loopback plug download

They take the form of either a single plug or a port-to-port cable with some communication connections shorted (looped-back).

G.823/G.Loopback connectors are designed for the testing of communication ports.

Mounting: Desk-top stackable, 19"/23" Rack mountable.

Dimensions: 438 x 44 x 225.5mm (W x H x D).Loopback: Local loopback, Line loopback Loopback:.Currently-Active Alarm Summary (CAAS) Diagnostics Test.Alarm Queue: Contains up to 200 alarm records of latest alarm types, alarm severity, date and time.Multiplexing: E1/T1 LOF, AIS, UAS, RAI/YEL.Switch, SFP Tx Fail, SFP Rx Fail, SFP Temperature Port Number Mismatch, Card Fail, Card Registration, MSP System Clock Loss, Log on and Log off, Optical Port Uneqp,Įthernet Link, Card In, Card Out, Card Type Mismatch, Card Alarm Cut Off, Power Loss/Uneqp, Fan Fail, Overheat,.

SDH/SONET Performance RS-BIP(B1), MS-BIP(B2), MS-REI, HP-BIP(B3), HP-REI, LP-BIP(V5), LP-REI(V5).System Performance RX-Lost, Cell-Lost, Jit-UR, Jit-OR.Second (BES), Severe Error Second (SES), Unavailable Second (UAS) Performance Reports: Date &Time, Error Block (EB), Background Block Error (BBE), Error Second (ES), Burst Error.Performance Store: The last 24-hour performance in 15-minute interval.Maximum Current: 1A for 30Vdc, 0.3A for 125 Vac.Initial Insulation Resistance: Minimal 1000 ohm (at 500Vdc).Output Signal: E1, T1, 2.048 MHz, 1.544 MHz (user selectable).Input Signal: E1, T1, 2.048 MHz, 1.544 MHz (user selectable).Primary/Secondary Clock: Internal, External, Line Clock from SDH/SONET, Line Clock from E1/T1and Adaptive Clock Recovery.Surge Protection: GR-1089 Intra-Building.Number of ports: 8 or 16 or 32, manufacture option.Framing: ITU G.704 (CRC: on/off, CAS: on/off, Unframed).Number of Ports: 8 or 16 or 32, manufacture option.Number of Ports : 2 Combo GbE (Including Electrical and Optical ports Auto-detection of SFP for highest priority).Please refer to SFP optical module brochure for detail.

#Metro e loopback plug download

General Specifications For more detailed information and ordering specifics on the many interface cards available for this product, please click here to download the multi-page printable data sheet. Support IPv4 Routing & IPv6* Routing over.C-VLAN/S-VLAN tag on management traffic.PPM version: conforms to G.823/G.824 Traffic.Up to 32 Pseudowires can apply Adaptive Clock.Backplane capacity: up to 252xVT11/VT12.Support TDM traffic emulation over MPLS*,.Support VC4 transparent/channelized STM-1.

#Metro e loopback plug code

6-bit DiffServ Code Point -DSCP field - ToS.

3-bit Priority Code Point - PCP field within.

Ingress Rate Limiting per Ethernet port with.

Support 803.3x Flow control on input ports.

802.1q Port-based VLAN on Ethernet port.

2 slots for hot-swappable plug-in cards:.

2 Combo GbE with SFP housing and RJ45 Connector.

Power Module: -48Vdc (Over-voltage protection and Load sharing).

Security is ensured via SSHv1/SSHv2 function and SNMPv1/v3 management. Of IP/MPLS* or Metro Ethernet network, Loop-IP6763 TDMoEthernet Aggregator utilizes Jitter BufferĬontrol and can compensate up to 512 ms with G.823/G.824 Traffic Interface conformance (+/- 1ppm). To compensate the inherent Packet Delay Variation (PDV) Loop-IP6763 TDMoEthernet Aggregator employs various Pseudowire Encapsulation protocols such as Stream along with the original timing information. Pseudowire device converts the received packet stream back to original PDH and SDH/SONET data Network via dual combo Gigabit Ethernet WAN ports with 802.3ad Link Aggregation capability. PDH and SDH/SONET ports into packets and transmits to the connected IP/MPLS* or Metro Ethernet Loop-IP6763 TDMoEthernet Aggregator converts the TDM data stream and timing information from both

As the core communications network migrates from legacy TDM to IP/MPLS or Metro Ethernet, this product allows you to leverage existing capital equipment and operations efficiently and at a relatively low cost. The E1/T1 SCSI interface is fixed on main board while there are two hot-swappable tributary slots for STM-1/OC-3 or STM-4/OC-12* plug-in card types. LAN traffic over existing IP/MPLS* or Metro Ethernet network.

Which allows operators to transport up to 32 E1/T1, 4 STM-1/OC-3 or 1 STM-4/OC-12* along with 4 Giga The Loop-IP6763 TDMoEthernet Aggregator provides a cost-effective solution Loop IP-6763 TDMoEthernet Aggregator T1, E1, STM-1, OC-3, STM-4, OC-12, GigE over Ethernet, MPLS, MetroE